Joining the Military

Shop Information Practice Test

Free · No signup

Tools, fasteners, materials and shop practice. 10 questions in 6 minutes, the shortest subtest on the test.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Sample Shop Information questions, with the answers

5 of the 10 questions in version A of this subtest, exactly as the test asks them. Every question on the test comes with an explanation like these after you answer.

  1. 1. A hand saw has a very narrow, thin blade held tight by a deep C-shaped frame, and it is used to cut intricate curves in wood. This saw is called a

    • A. coping saw
    • B. hacksaw
    • C. back saw
    • D. rip saw

    Answer: A. A coping saw holds a narrow, thin blade in tension in a deep C-shaped frame and is used for cutting intricate curves. The hacksaw is the tempting choice because it also holds its blade in tension, but its fine-toothed blade is made for cutting metals and some plastics, not curves in wood.

    Remember: Coping saw = curves in wood. Hacksaw = metal. Back saw = straight, accurate cuts such as miters in a miter box.

    Checked against Louisiana State University, Design Shop Safety Manual.

  2. 2. The striking end of a cold chisel has spread out and cracked into a mushroom shape. What should you do?

    • A. Keep using it but wear work gloves
    • B. Strike it with lighter hammer blows
    • C. Stop using it until the head is reground
    • D. Use it only as a small pry bar

    Answer: C. OSHA warns that a mushroomed head on a chisel, wedge, or drift pin can shatter when struck and send sharp fragments flying toward the user or nearby workers, so impact tools must be kept free of mushroomed heads. Gloves or lighter blows do not stop the flying fragments, and OSHA also warns that misusing a chisel can break off its tip.

    Remember: Any tool you strike with a hammer must be kept free of a mushroomed head. Do not use it again until the mushroom is ground off or the tool is replaced.

    Checked against OSHA 3080, Hand and Power Tools.

  3. 3. Lumber from cone-bearing trees with needlelike leaves, such as pines and firs, is classified as

    • A. hardwood
    • B. softwood
    • C. plywood
    • D. heartwood

    Answer: B. Softwoods come from conifers (gymnosperms), which usually bear cones and have needle or scale leaves. Hardwoods come from broadleaf flowering trees. The names describe the tree type, not how hard the wood is: longleaf pine, a softwood, is harder than basswood, a hardwood.

    Remember: Softwood = conifer (pine, fir, spruce, cedar). Hardwood = broadleaf tree (oak, maple, walnut). The label is botanical, not a hardness test.

    Checked against USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282), ch. 2, Characteristics and Availability of Commercially Important Woods.

  4. 4. On a metric micrometer, the sleeve shows the 7 mm line plus one more half-millimeter line, and line 22 on the thimble lines up with the reading line. Each thimble line is 0.01 mm. What is the reading?

    • A. 7.22 mm
    • B. 7.72 mm
    • C. 7.522 mm
    • D. 9.70 mm

    Answer: B. Add the three parts: 7 mm from the sleeve, 0.5 mm for the extra half-millimeter line, and 22 × 0.01 = 0.22 mm from the thimble. The total is 7 + 0.5 + 0.22 = 7.72 mm. Forgetting the half-millimeter line gives 7.22 mm.

    Remember: Metric micrometer: whole millimeters + any half-millimeter line on the sleeve + thimble line × 0.01 mm.

    Checked against L.S. Starrett, 436.1 Outside Micrometer User Manual (How to Read a Micrometer).

  5. 5. Drawer fronts are often joined to the drawer sides with interlocking, wedge-shaped pins and tails. The main reason is that this joint

    • A. needs no glue or fasteners at all
    • B. is the quickest joint to cut
    • C. resists being pulled apart
    • D. hides all of its end grain

    Answer: C. This is a dovetail joint. The shape of the tails and pins means the joint cannot be pulled apart, so it resists the pulling forces on a drawer front well. It is more time-consuming to make than a box joint, and its strength also comes from a large glue surface, so glue is still used.

    Remember: Dovetails lock against pulling forces, so they show up where something is pulled again and again, such as drawer fronts.

    Checked against University of Illinois School of Art and Design, Woodworking: Making Joints.

The format of all ten subtests, how the AFQT is scored and how to study for it are on the ASVAB practice test hub.

What Shop Information covers

Hand and power tools, measuring tools, fasteners, wood, metal, joints, layout, shop safety and building materials. On the computer test Shop and Auto are separate subtests, reported together as one Auto and Shop (AS) score.

It does not count toward your AFQT. It feeds the line scores and composites each service uses to match you to jobs: see how the Army, Navy, Air Force and Marine Corps use it, or take the full ASVAB.

Keep going

officialasvab.com (What to Expect, Scores, FAQs, CAT-ASVAB, PiCAT, retest policy), ASVAB Technical Bulletin No. 4, Segall (2004), DoDI 1145.01, and each service's recruiting site, read October 3, 2026

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.