Joining the Military

ASVAB Electronics Information Practice Test 3

Free · No signup

Test 3 of 5 for Electronics Information: 15 questions in 10 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 8 of Electronics Information practice test 3

8 of the 15 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 15, with an explanation like these for every question.

  1. 1. Materials such as glass and rubber, which do not let electric charge move through them easily, are called

    • A. conductors
    • B. superconductors
    • C. insulators
    • D. semiconductors
    Show the answer to question 1

    Answer: C. In insulators, electrons are bound in the structure and cannot move freely, so charge does not flow through them easily. Conductors such as metals have free electrons. Semiconductors fall between the two.

    Remember: Conductors (metals) let charge flow; insulators (glass, rubber, plastic) block it.

    Checked against OpenStax College Physics 2e, 18.2 Conductors and Insulators.

  2. 2. What is the current in the circuit shown, where a 6-volt battery is connected to a 3-ohm resistor?

    +6 VR1 = 3 Ω
    • A. 0.5 ampere
    • B. 9 amperes
    • C. 2 amperes
    • D. 18 amperes
    Show the answer to question 2

    Answer: C. Ohm's law: I = V / R = 6 / 3 = 2 amperes. Multiplying (18) or dividing 3 by 6 (0.5) are the usual mistakes.

    Remember: Current goes up with voltage and down with resistance: I = V / R.

    Checked against OpenStax College Physics 2e, 20.2 Ohm's Law: Resistance and Simple Circuits.

  3. 3. Which ladder does OSHA require when the worker or the ladder could contact exposed energized electrical parts?

    • A. An aluminum ladder
    • B. A steel ladder
    • C. Any ladder tall enough to reach the work
    • D. A ladder with nonconductive side rails
    Show the answer to question 3

    Answer: D. OSHA requires portable ladders to have nonconductive side rails, such as fiberglass, if they are used where the employee or the ladder could contact exposed energized parts. Aluminum and steel are metals that conduct electricity.

    Remember: Metal conducts: near live parts use fiberglass or other nonconductive ladders.

    Checked against OSHA 29 CFR 1910.333, Selection and use of work practices.

  4. 4. An electromagnet is made by

    • A. rubbing a glass rod with silk
    • B. passing electric current through a coil of wire
    • C. heating a bar of copper
    • D. cooling a piece of iron in ice water
    Show the answer to question 4

    Answer: B. Electromagnets use electric current to make magnetism. A current-carrying coil produces a field like a bar magnet, and an iron core makes it much stronger. Rubbing glass with silk makes static charge, not a magnet.

    Remember: Current through a coil makes a magnet; add an iron core to strengthen it; switch off the current to turn it off.

    Checked against OpenStax College Physics 2e, 22.2 Ferromagnets and Electromagnets.

  5. 5. On a schematic diagram, a zigzag line represents a

    • A. battery
    • B. switch
    • C. resistor
    • D. capacitor
    Show the answer to question 5

    Answer: C. The zigzag element on a circuit diagram is a resistor, a part that provides a known resistance. A battery is drawn as long and short parallel lines, and a capacitor as two parallel lines of equal length.

    Remember: Zigzag = resistor (the jagged path suggests opposition to current).

    Checked against OpenStax Physics, 19.2 Series Circuits.

  6. 6. In the circuit shown, a 12-volt battery is connected in series with resistors of 1, 2 and 3 ohms. What is the voltage across the 3-ohm resistor?

    +12 VR1 = 1 ΩR2 = 2 ΩR3 = 3 Ω
    • A. 4 volts
    • B. 6 volts
    • C. 12 volts
    • D. 2 volts
    Show the answer to question 6

    Answer: B. The total resistance is 1 + 2 + 3 = 6 ohms, so the current is 12 / 6 = 2 amperes. The voltage across the 3-ohm resistor is 2 x 3 = 6 volts. Splitting 12 volts equally among the three resistors would give 4 volts, which ignores their different sizes.

    Remember: Find the series current first, then multiply by each resistor to get its voltage drop.

    Checked against OpenStax College Physics 2e, 21.1 Resistors in Series and Parallel.

  7. 7. A 1,500-watt space heater runs on 120 volts. How much current does it draw?

    • A. 1.25 amperes
    • B. 125 amperes
    • C. 12.5 amperes
    • D. 0.08 ampere
    Show the answer to question 7

    Answer: C. Since P = I x V, the current is I = P / V = 1,500 / 120 = 12.5 amperes. Dividing the other way (120 / 1,500 = 0.08) gives a number that is far too small for a heater.

    Remember: Current = watts divided by volts (I = P / V).

    Checked against OpenStax College Physics 2e, 20.4 Electric Power and Energy.

  8. 8. An ammeter is designed to have a very low internal resistance so that

    • A. it draws almost no current from the circuit
    • B. it does not noticeably change the current it measures
    • C. it can be connected across a voltage source
    • D. it never needs a fuse
    Show the answer to question 8

    Answer: B. All the current being measured passes through an ammeter, so its resistance must be very small; otherwise adding it would change the circuit and the current. Drawing almost no current is the goal of a voltmeter, which has a very high resistance. Ammeters usually contain a fuse.

    Remember: Ammeter: low resistance, in series. Voltmeter: high resistance, in parallel.

    Checked against OpenStax University Physics Volume 2, 10.4 Electrical Measuring Instruments.

What Electronics Information practice test 3 covers

15 questions in 10 minutes, the length and time limit of the Electronics Information subtest on the computer ASVAB. 3 of them are asked with a diagram. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 3 spreads its questions over 12 topics:

TopicQuestions in test 3
Current, voltage and resistance2
Ohm's law1
Electrical safety1
Magnetism and induction1
Schematic symbols1
Series and parallel circuits2
Electrical power2
Meters and tools1
AC and DC1
Diodes and transistors1
Wire and wiring1
Components1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Electronics Information tests, and test 3 of the other subtests

What the Electronics Information subtest covers, how it is used and the questions people ask about it are on the Electronics Information practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Electronics Information tests

Practice test 3 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.