Joining the Military

ASVAB Shop Information Practice Test 3

Free · No signup

Test 3 of 5 for Shop Information: 10 questions in 6 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 6 of Shop Information practice test 3

6 of the 10 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 10, with an explanation like these for every question.

  1. 1. Which hand tool has a blade that is adjusted to a set depth and is pushed down and forward along a board, with the grain, to shave off a fine cut and smooth the surface?

    • A. rasp
    • B. plane
    • C. chisel
    • D. file
    Show the answer to question 1

    Answer: B. This describes a plane, such as a block plane. You check that its blade is adjusted to the proper depth, apply pressure down and forward, and plane with the grain, setting the blade for a fine cut on difficult grain. A chisel, rasp, and file are also hand tools for working wood, but the plane is the one used this way.

    Remember: Plane: set the blade depth, push down and forward, and always plane with the grain. When it is not in use, set it on its side to protect the blade.

    Checked against Louisiana State University, Design Shop Safety Manual.

  2. 2. OSHA warns that you should never carry a portable power tool by its

    • A. main handle
    • B. carrying case
    • C. side grip
    • D. cord or hose
    Show the answer to question 2

    Answer: D. OSHA lists "Never carry a tool by the cord or hose" first among its general power tool precautions, followed by never yanking the cord or hose to disconnect it from the receptacle. Carry the tool by its handle instead.

    Remember: Cords and hoses carry power, not tools. Carry by the handle, and pull the plug, not the cord.

    Checked against OSHA 3080, Hand and Power Tools.

  3. 3. A dry, surfaced 2 by 4 stud actually measures about

    • A. 1-1/2 by 3-1/2 inches
    • B. 2 by 4 inches
    • C. 1-3/4 by 3-3/4 inches
    • D. 1-1/4 by 3-1/4 inches
    Show the answer to question 3

    Answer: A. Lumber widths and thicknesses are named by nominal size, and the dressed size is smaller. The American Softwood Lumber Standard sizes in the Wood Handbook list a dry 2 by 4 as 1-1/2 by 3-1/2 inches. A tape measure on a 2 by 4 will never read a full 2 by 4 inches.

    Remember: Dimension lumber loses about 1/2 inch from each nominal size up to 6 inches: 2x4 is 1-1/2 x 3-1/2, and 2x6 is 1-1/2 x 5-1/2.

    Checked against USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282), ch. 6, Commercial Lumber, Round Timbers, and Ties, Table 6-6.

  4. 4. As a freshly sawn board dries, in which direction does it shrink the least?

    • A. across the growth rings (radially)
    • B. along the growth rings (tangentially)
    • C. along its length, parallel to the grain
    • D. about equally in all directions
    Show the answer to question 4

    Answer: C. Shrinkage along the grain is very small, usually only 0.1% to 0.2% from green to ovendry, so a board barely gets shorter. Across the grain it shrinks much more, and tangential shrinkage is about twice radial shrinkage. That difference is why drying boards can cup or distort.

    Remember: Wood shrinks most around the rings (tangential), about half as much across them (radial), and hardly at all along the length.

    Checked against USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282), ch. 4, Moisture Relations and Physical Properties of Wood.

  5. 5. On an inch micrometer, the sleeve shows the 3 line (0.300 inch) plus 2 more small lines (0.025 inch each), and line 14 on the thimble lines up with the reading line. Each thimble line is 0.001 inch. The reading is

    • A. 0.314 inch
    • B. 0.334 inch
    • C. 0.350 inch
    • D. 0.364 inch
    Show the answer to question 5

    Answer: D. Add the sleeve and thimble: 0.300 + (2 × 0.025) + (14 × 0.001) = 0.300 + 0.050 + 0.014 = 0.364 inch. Answering 0.314 inch leaves out the two small sleeve lines, and 0.350 inch forgets the thimble reading.

    Remember: Inch micrometer: numbered sleeve lines are tenths (0.100), small lines are 0.025 each, and each thimble line is 0.001. Add all three.

    Checked against L.S. Starrett, 436.1 Outside Micrometer User Manual (How to Read a Micrometer).

  6. 6. Which portable power tool can cut a curved outline in a sheet of plywood?

    • A. jigsaw
    • B. circular saw
    • C. miter saw
    • D. table saw
    Show the answer to question 6

    Answer: A. A jigsaw uses a short, straight blade that moves up and down, so it can follow straight or curved lines in moderately thin stock. Saws with circular blades, including portable circular saws, can make only straight cuts and must never be forced around a curve.

    Remember: Circular blade = straight cuts only. Straight reciprocating blade (jigsaw, scroll saw) or narrow band blade = curves.

    Checked against Louisiana State University, Design Shop Safety Manual.

What Shop Information practice test 3 covers

10 questions in 6 minutes, the length and time limit of the Shop Information subtest on the computer ASVAB. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 3 spreads its questions over 10 topics:

TopicQuestions in test 3
Hand tools1
Shop safety1
Building materials1
Wood and woodworking1
Measuring tools1
Power tools1
Layout and marking1
Joints1
Metal and metalworking1
Fasteners1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Shop Information tests, and test 3 of the other subtests

What the Shop Information subtest covers, how it is used and the questions people ask about it are on the Shop Information practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Shop Information tests

Practice test 3 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.