Questions 8 to 10 of Shop Information practice test 1
3 of the 10 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 10, with an explanation like these for every question.
8. Freshly placed portland cement concrete hardens and gains strength mainly because
- A. the water evaporates and the mix dries
- B. the sand and gravel fuse together
- C. air bubbles expand and lock the stones
- D. the cement reacts chemically with water
Show the answer to question 8
Answer: D. Portland cement is a hydraulic cement: it sets and hardens through a chemical reaction with water called hydration, and the hardened paste binds the sand and gravel together. Simple drying is the tempting answer, but the strength comes from the reaction, not from the water leaving. The aggregate acts as filler and does not fuse.
Remember: Concrete = cement + water + sand + gravel. The cement and water react (hydration) to form the glue that holds the stones together.
Checked against FHWA-RD-97-148, Portland Cement Concrete Pavement: Application Description.
9. Tap drill size for cut threads can be found by subtracting the thread pitch (1 divided by threads per inch) from the nominal diameter. What tap drill size does this give for a 1/2-13 thread (1/2 inch diameter, 13 threads per inch)?
- A. 0.077 inch
- B. 0.423 inch
- C. 0.462 inch
- D. 0.500 inch
Show the answer to question 9
Answer: B. The pitch is 1 ÷ 13 ≈ 0.077 inch. Subtract it from the 0.500 inch diameter: 0.500 - 0.077 = 0.423 inch, which matches a 27/64 inch (0.422) drill. Choosing 0.077 inch stops after finding the pitch, and 0.500 inch would leave no metal for the tap to cut into threads.
Remember: Tap drill ≈ nominal diameter - pitch, where pitch = 1 ÷ threads per inch. The hole must be smaller than the bolt so the tap has metal to cut.
Checked against Introduction to Machining (Washington SBCTC open textbook), 5.9 Tap and Dies.
10. A rectangular slab form is staked out 12 feet by 16 feet. If all four corners are square, each diagonal should measure
- A. 20 feet
- B. 14 feet
- C. 24 feet
- D. 28 feet
Show the answer to question 10
Answer: A. A 12 by 16 rectangle is the 3-4-5 triangle multiplied by 4, so the diagonal is 5 × 4 = 20 feet (the square root of 144 + 256 = 400). When the corners are square, the two diagonals are equal. Adding the two sides to get 28 feet is the tempting mistake.
Remember: To check a layout for square, measure both diagonals: they must be equal. Any multiple of 3-4-5 (6-8-10, 9-12-15, 12-16-20) gives a right angle.
Checked against Quikrete, Layout Basics for Slabs and Footers.
What Shop Information practice test 1 covers
10 questions in 6 minutes, the length and time limit of the Shop Information subtest on the computer ASVAB. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 1 spreads its questions over 10 topics:
| Topic | Questions in test 1 |
|---|---|
| Hand tools | 1 |
| Shop safety | 1 |
| Wood and woodworking | 1 |
| Fasteners | 1 |
| Power tools | 1 |
| Measuring tools | 1 |
| Joints | 1 |
| Building materials | 1 |
| Metal and metalworking | 1 |
| Layout and marking | 1 |
Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.
The other Shop Information tests, and test 1 of the other subtests
What the Shop Information subtest covers, how it is used and the questions people ask about it are on the Shop Information practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.
