Joining the Military

ASVAB Mechanical Comprehension Practice Test 1

Free · No signup

Test 1 of 5 for Mechanical Comprehension: 15 questions in 22 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 8 to 14 of Mechanical Comprehension practice test 1

7 of the 15 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 15, with an explanation like these for every question.

  1. 8. A spring stretches 2 inches when a 10 lb weight hangs from it. Staying within its elastic limit, how far will it stretch with a 25 lb weight?

    • A. 4 inches
    • B. 2.5 inches
    • C. 5 inches
    • D. 12.5 inches
    Show the answer to question 8

    Answer: C. By Hooke's law the stretch is proportional to the force. The spring stretches 2 / 10 = 0.2 inch per pound, so 25 lb gives 5 inches. The 12.5 inch choice divides the new weight by the old stretch.

    Remember: Hooke's law: stretch is proportional to force. Find the stretch per pound, then multiply by the new load.

    Checked against OpenStax College Physics 2e, 16.1 Hooke's Law: Stress and Strain Revisited.

  2. 9. Concrete dams are usually built much thicker at the bottom than at the top. Why?

    • A. Water pressure increases with depth
    • B. Water is warmer near the bottom
    • C. Water pushes hardest at the surface
    • D. The top must carry road traffic
    Show the answer to question 9

    Answer: A. Pressure from a liquid grows with depth (P = h x density x g), so the force on each foot of dam is greatest near the bottom. The dam is thickened there to resist that larger push. Water pressure is smallest, not largest, at the surface.

    Remember: Liquid pressure depends on depth: the deeper the point, the greater the pressure on a wall, tank side or dam.

    Checked against OpenStax College Physics 2e, 11.4 Variation of Pressure with Depth in a Fluid.

  3. 10. Four rods have the same length and thickness and carry the same pulling load. Which rod will stretch the least?

    • A. Brass
    • B. Lead
    • C. Steel
    • D. Aluminum
    Show the answer to question 10

    Answer: C. Stretch under a given load is smaller when Young's modulus (stiffness) is larger. Steel's modulus, about 210 x 109 N/m2, is far above brass (90), aluminum (70) and lead (16). Lead stretches the most of the four.

    Remember: Stiffer material (higher modulus) means less stretch for the same load. Steel is one of the stiffest common metals.

    Checked against OpenStax College Physics 2e, 5.3 Elasticity: Stress and Strain.

  4. 11. Standing passengers lurch forward when a bus stops suddenly. This happens because

    • A. their bodies tend to keep moving forward
    • B. gravity pulls harder during stops
    • C. the brakes push them forward
    • D. the floor speeds up under them
    Show the answer to question 11

    Answer: A. This is Newton's first law, inertia: a body in motion stays in motion unless a net force acts on it. The bus slows, but the passengers' bodies keep moving until friction at their feet or a handrail stops them. No forward push from the brakes acts on them.

    Remember: Inertia: objects keep doing what they were doing (resting or moving steadily) until a net force changes it.

    Checked against OpenStax College Physics 2e, 4.2 Newton's First Law of Motion: Inertia.

  5. 12. Water flows steadily through a pipe that narrows from a cross-sectional area of 6 square inches to 2 square inches. If the water moves at 3 ft per second in the wide part, how fast does it move in the narrow part?

    • A. 1 ft per second
    • B. 9 ft per second
    • C. 3 ft per second
    • D. 18 ft per second
    Show the answer to question 12

    Answer: B. The same volume must pass every point each second, so area x speed stays constant: 6 x 3 = 2 x speed, giving 9 ft/s. Water does not slow down in a narrow section; speed increases when the area decreases.

    Remember: Continuity: area x speed stays the same along a pipe. Narrow section, faster flow, like a hose nozzle.

    Checked against OpenStax College Physics 2e, 12.1 Flow Rate and Its Relation to Velocity.

  6. 13. A 600 lb crate rests on the floor on a flat base that measures 3 ft by 2 ft. What pressure does the crate put on the floor?

    • A. 120 lb per square foot
    • B. 3,600 lb per square foot
    • C. 200 lb per square foot
    • D. 100 lb per square foot
    Show the answer to question 13

    Answer: D. Pressure is force divided by the area it acts on. The base area is 3 x 2 = 6 sq ft, so P = 600 / 6 = 100 lb per sq ft. The 3,600 choice multiplies by the area instead of dividing.

    Remember: Pressure = force / area. Spread the same force over more area and the pressure drops.

    Checked against OpenStax College Physics 2e, 11.3 Pressure.

  7. 14. The 10 ft bar in the diagram balances on a fulcrum at its center. A 30 lb weight hangs 4 ft left of the fulcrum and a 40 lb weight hangs 2 ft left of it. What weight at the right end keeps the bar level? (Ignore the bar's weight.)

    30 lb40 lb?4 ft2 ft5 ft
    • A. 40 lb
    • B. 70 lb
    • C. 50 lb
    • D. 35 lb
    Show the answer to question 14

    Answer: A. Add the turning effects on the left: 30 x 4 + 40 x 2 = 200 lb-ft. The right end is 5 ft from the fulcrum, so the weight is 200 / 5 = 40 lb. The 70 lb choice just adds the weights and ignores their distances.

    Remember: For several weights, add each weight times its distance on one side, then divide by the distance on the other side.

    Checked against OpenStax College Physics 2e, 9.2 The Second Condition for Equilibrium.

What Mechanical Comprehension practice test 1 covers

15 questions in 22 minutes, the length and time limit of the Mechanical Comprehension subtest on the computer ASVAB. 6 of them are asked with a diagram. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 1 spreads its questions over 13 topics:

TopicQuestions in test 1
Levers2
Pulleys2
Gears1
Ramps and inclined planes1
Wheel and axle1
Screws and wedges1
Hydraulics1
Springs1
Structures and loads1
Materials and their strength1
Motion1
Fluids1
Pressure1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Mechanical Comprehension tests, and test 1 of the other subtests

What the Mechanical Comprehension subtest covers, how it is used and the questions people ask about it are on the Mechanical Comprehension practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Mechanical Comprehension tests

Practice test 1 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.