Questions 1 to 7 of Mechanical Comprehension practice test 5
7 of the 15 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 15, with an explanation like these for every question.
1. The seesaw in the diagram has its fulcrum at the center. An 80 lb child sits 3 ft from the fulcrum. What weight placed 4 ft from the fulcrum on the other side balances the seesaw?
- A. 60 lb
- B. 80 lb
- C. 107 lb
- D. 20 lb
Show the answer to question 1
Answer: A. Balance the turning effects about the fulcrum: 80 x 3 = W x 4, so W = 240 / 4 = 60 lb. The weight that sits farther from the fulcrum can be lighter. The 107 lb choice swaps the two distances, and 80 lb ignores the distances.
Remember: Weight x distance on one side = weight x distance on the other. Measure every distance from the fulcrum, not from the end.
Checked against OpenStax College Physics 2e, 9.2 The Second Condition for Equilibrium.
2. In the diagram, a 12-tooth gear drives a 36-tooth gear. When the 12-tooth gear makes 6 full turns, how many turns does the 36-tooth gear make?
- A. 18
- B. 3
- C. 2
- D. 6
Show the answer to question 2
Answer: C. Meshing gears pass the same number of teeth. Six turns of the small gear move 6 x 12 = 72 teeth, and 72 / 36 = 2 turns of the large gear. The 18 choice multiplies by 3 when it should divide; the larger gear always turns fewer times.
Remember: Turns x teeth is the same for both gears. The gear with three times the teeth makes one third the turns.
Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.
3. A valve has a handwheel 12 inches in diameter mounted on a stem 1.5 inches in diameter. What is the ideal mechanical advantage of this wheel and axle?
- A. 18
- B. 8
- C. 10.5
- D. 13.5
Show the answer to question 3
Answer: B. For a wheel and axle, IMA = wheel radius / axle radius. The ratio of the diameters is the same as the ratio of the radii: 12 / 1.5 = 8. The 18 choice multiplies the two numbers, and 10.5 subtracts them.
Remember: Wheel and axle IMA = big radius / small radius. Diameters work too, as long as you use the same measure for both.
Checked against OpenStax Physics, 9.3 Simple Machines.
4. A steel spoon and a wooden spoon have been lying in the same cool room for hours. The steel spoon feels colder to the touch because steel
- A. is at a lower temperature than the wood
- B. holds no heat of its own
- C. reflects the heat of your skin back at you
- D. conducts heat away from your hand faster
Show the answer to question 4
Answer: D. Both spoons are at room temperature. Metals are good conductors of heat, so the steel carries heat away from your skin faster than the wood does, and your hand cools more. Lower temperature is the tempting mistake: what you feel is the rate of heat flow, not the temperature of the spoon.
Remember: Metals conduct heat well; wood and plastic insulate. That is why pan handles are often wood or plastic.
Checked against OpenStax College Physics 2e, 14.5 Conduction.
5. A 15 lb weight stretches a spring 3 inches. What is the force constant (spring constant) of the spring?
- A. 45 lb per inch
- B. 18 lb per inch
- C. 0.2 lb per inch
- D. 5 lb per inch
Show the answer to question 5
Answer: D. By Hooke's law, force = k x stretch, so k = force / stretch = 15 / 3 = 5 lb per inch. The 0.2 choice divides the wrong way, giving inches per pound, and 45 multiplies the two numbers.
Remember: Spring constant = force / stretch. A stiffer spring has a larger constant.
Checked against OpenStax College Physics 2e, 16.1 Hooke's Law: Stress and Strain Revisited.
6. In the diagram, a 90 lb load hangs from one movable pulley that itself weighs 10 lb. Two rope strands support the pulley. Ignoring friction, what pull on the rope holds the load steady?
- A. 45 lb
- B. 50 lb
- C. 100 lb
- D. 40 lb
Show the answer to question 6
Answer: B. The two strands hold up the load and the movable pulley together: 90 + 10 = 100 lb. Each strand carries half, so the pull is 100 / 2 = 50 lb. The 45 lb choice forgets that the pulley must be lifted too.
Remember: Pull = total weight hanging from the movable pulley / number of supporting strands. Count the pulley itself when its weight is given.
Checked against OpenStax Physics, 9.3 Simple Machines.
7. A 20-tooth gear turning at 240 revolutions per minute (rpm) must drive a second gear at 80 rpm. How many teeth must the second gear have?
- A. 60 teeth
- B. 40 teeth
- C. 7 teeth
- D. 80 teeth
Show the answer to question 7
Answer: A. Speed x teeth is the same for both gears: 240 x 20 = 80 x teeth, so teeth = 4,800 / 80 = 60. The second gear must turn at one third the speed, so it needs three times the teeth. The 7 choice divides by 3 when it should multiply; a slower gear is always the larger one.
Remember: To slow a gear train down, the driven gear needs more teeth. Teeth needed = driver teeth x driver rpm / wanted rpm.
Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.
What Mechanical Comprehension practice test 5 covers
15 questions in 22 minutes, the length and time limit of the Mechanical Comprehension subtest on the computer ASVAB. 4 of them are asked with a diagram. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 5 spreads its questions over 13 topics:
| Topic | Questions in test 5 |
|---|---|
| Levers | 2 |
| Gears | 2 |
| Wheel and axle | 1 |
| Materials and their strength | 1 |
| Springs | 1 |
| Pulleys | 1 |
| Ramps and inclined planes | 1 |
| Hydraulics | 1 |
| Screws and wedges | 1 |
| Motion | 1 |
| Structures and loads | 1 |
| Fluids | 1 |
| Pressure | 1 |
Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.
The other Mechanical Comprehension tests, and test 5 of the other subtests
What the Mechanical Comprehension subtest covers, how it is used and the questions people ask about it are on the Mechanical Comprehension practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.
