Joining the Military

ASVAB Mechanical Comprehension Practice Test 4

Free · No signup

Test 4 of 5 for Mechanical Comprehension: 15 questions in 22 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 7 of Mechanical Comprehension practice test 4

7 of the 15 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 15, with an explanation like these for every question.

  1. 1. The lever in the diagram is 9 ft long. The fulcrum is 3 ft from the load at the left end, and the effort pushes down at the right end. What is the ideal mechanical advantage?

    LoadEffort3 ft6 ft
    • A. 1/2
    • B. 6
    • C. 3
    • D. 2
    Show the answer to question 1

    Answer: D. IMA = effort arm / load arm. The effort arm is 9 - 3 = 6 ft and the load arm is 3 ft, so IMA = 6 / 3 = 2. The 1/2 choice divides the arms the wrong way.

    Remember: Lever IMA = effort arm length / load arm length, both measured from the fulcrum.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  2. 2. The diagram shows a 70 lb load on one movable pulley held by two rope strands. If the worker pulls 10 ft of rope through, how far does the load rise?

    70 lbPull
    • A. 5 ft
    • B. 20 ft
    • C. 2.5 ft
    • D. 10 ft
    Show the answer to question 2

    Answer: A. With two supporting strands, each strand shortens by half the rope pulled, so the load rises 10 / 2 = 5 ft. The pull is halved to 35 lb, and the distance the load moves is halved too.

    Remember: Load distance = rope pulled / number of supporting strands.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  3. 3. In the diagram, a 30-tooth gear A turns clockwise and drives a 15-tooth gear B. How does gear B turn?

    Gear A30 teeth, driverGear B15 teeth
    • A. Clockwise, slower than A
    • B. Counterclockwise, slower than A
    • C. Counterclockwise, faster than A
    • D. Clockwise, faster than A
    Show the answer to question 3

    Answer: C. Two meshing gears turn in opposite directions, so B turns counterclockwise. B has half as many teeth, so it makes 2 turns for each turn of A. A smaller driven gear turns faster, not slower.

    Remember: Meshing gears reverse direction; the gear with fewer teeth spins faster.

    Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.

  4. 4. A 400 lb crate is pushed up the ramp shown, which is 10 ft long and 2 ft high. Because of friction, the push needed is 100 lb. What is the efficiency of the ramp?

    400 lb10 ft2 ft
    • A. 20%
    • B. 25%
    • C. 80%
    • D. 125%
    Show the answer to question 4

    Answer: C. Work out = 400 lb x 2 ft = 800 ft-lb. Work in = 100 lb x 10 ft = 1,000 ft-lb. Efficiency = 800 / 1,000 = 80%. The 125% choice divides the wrong way; no machine puts out more work than it takes in.

    Remember: Efficiency = work out / work in x 100. Friction always keeps it below 100%.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  5. 5. A winch has an axle radius of 2 inches. Ignoring friction, what crank radius lets a 30 lb effort lift a 360 lb load?

    • A. 12 inches
    • B. 6 inches
    • C. 24 inches
    • D. 180 inches
    Show the answer to question 5

    Answer: C. The needed IMA is 360 / 30 = 12. Since IMA = crank radius / axle radius, the crank radius is 12 x 2 = 24 inches. The 12 inch choice is the advantage itself, not the radius.

    Remember: Wheel and axle: wheel radius = axle radius x needed mechanical advantage.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  6. 6. A screw is best described as

    • A. an inclined plane wrapped around a cylinder
    • B. a pulley with a single groove
    • C. a lever with the fulcrum at its tip
    • D. a wedge with two flat sides
    Show the answer to question 6

    Answer: A. A screw thread is a long ramp wound around a shaft, so turning it moves a load a short distance along the axis with a small turning force. It is often turned with a lever such as a wrench or screwdriver. A wedge is two inclined planes back to back, not a screw.

    Remember: Screw = ramp wrapped around a post. Finer threads (smaller pitch) mean more turns but less force.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  7. 7. In a car's hydraulic brake system, pressing the pedal raises the pressure in the brake fluid. That pressure increase

    • A. disappears once the fluid moves
    • B. stays only near the pedal cylinder
    • C. is greatest at the farthest wheel
    • D. reaches every part of the fluid equally
    Show the answer to question 7

    Answer: D. Pascal's principle: a change in pressure applied to an enclosed fluid is transmitted undiminished to all parts of the fluid and the container walls. So every wheel cylinder gets the same pressure increase. It does not fade with distance.

    Remember: Pascal's principle: press on a trapped liquid and the extra pressure shows up everywhere in it, the basis of brakes and lifts.

    Checked against OpenStax College Physics 2e, 11.5 Pascal's Principle.

What Mechanical Comprehension practice test 4 covers

15 questions in 22 minutes, the length and time limit of the Mechanical Comprehension subtest on the computer ASVAB. 6 of them are asked with a diagram. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 4 spreads its questions over 13 topics:

TopicQuestions in test 4
Levers2
Pulleys1
Gears2
Ramps and inclined planes1
Wheel and axle1
Screws and wedges1
Hydraulics1
Springs1
Structures and loads1
Materials and their strength1
Motion1
Fluids1
Pressure1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Mechanical Comprehension tests, and test 4 of the other subtests

What the Mechanical Comprehension subtest covers, how it is used and the questions people ask about it are on the Mechanical Comprehension practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Mechanical Comprehension tests

Practice test 4 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.