Joining the Military

ASVAB Shop Information Practice Test 4

Free · No signup

Test 4 of 5 for Shop Information: 10 questions in 6 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 7 of Shop Information practice test 4

7 of the 10 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 10, with an explanation like these for every question.

  1. 1. Before switching on a drill press, you must make sure you have removed the

    • A. depth stop
    • B. scrap backer board
    • C. table lock lever
    • D. chuck key
    Show the answer to question 1

    Answer: D. Remove the chuck key from the chuck as soon as you finish tightening the bit. OSHA training material warns that a key left in the chuck will be thrown from it when the spindle is turned on and can cause injury.

    Remember: Key out before power on. Never leave the chuck key in the chuck.

    Checked against OSHA (Susan Harwood grant training), Drill Press: Train the Trainer.

  2. 2. A pointed weight hung on a string is used during layout to find

    • A. true horizontal
    • B. true vertical
    • C. a 45-degree angle
    • D. the center of a circle
    Show the answer to question 2

    Answer: B. This is a plumb bob, a pointed weight on a string used for determining true vertical. Gravity pulls the weight straight down, so the string hangs plumb. A level, with its bubble gauges, is the tool for true horizontal.

    Remember: Plumb = vertical (plumb bob). Level = horizontal (spirit level).

    Checked against Louisiana State University, Design Shop Safety Manual.

  3. 3. The simplest wood joint, in which one piece is set against another and held mainly by nails or screws, is the

    • A. dovetail joint
    • B. mortise-and-tenon joint
    • C. butt joint
    • D. tongue-and-groove joint
    Show the answer to question 3

    Answer: C. In a butt joint one piece is simply butted against another and fastened, most often with nails or screws. Glue adds some strength, but the joint depends mainly on its fasteners. It is common in wall framing. Dovetail and mortise-and-tenon joints require cutting interlocking parts.

    Remember: Butt joint = no interlocking cuts, just pieces butted together and fastened. Simple and quick, but weaker than joints with interlocking cuts.

    Checked against University of Illinois School of Art and Design, Woodworking: Making Joints.

  4. 4. Why should a wood chisel never be used as a pry bar or wedge?

    • A. Its hard steel is brittle and can snap
    • B. Its soft steel bends too easily
    • C. Prying makes the bevel grow longer
    • D. Prying magnetizes the steel blade
    Show the answer to question 4

    Answer: A. A wood chisel's steel blade is heat treated throughout so it can be sharpened along its whole length. That makes the steel hard and brittle, so prying or wedging can snap it. The steel is not soft, so bending is not the main danger.

    Remember: Use each tool only for its job: a chisel cuts, a pry bar pries, a screwdriver drives screws.

    Checked against Louisiana State University, Design Shop Safety Manual.

  5. 5. Before an abrasive grinding wheel is mounted, it is tapped gently with a light nonmetallic tool. A sound, undamaged wheel will

    • A. make a dull thud
    • B. give a clear ringing tone
    • C. vibrate without any sound
    • D. spark where it is tapped
    Show the answer to question 5

    Answer: B. This is the ring test. OSHA says a stable, undamaged wheel gives a clear metallic tone, or ring, when tapped. A wheel that sounds cracked or dead must not be used, because it could fly apart at operating speed.

    Remember: Ring test: clear ring = OK; dull thud = cracked, do not mount. Also stand out of line with the wheel when starting a grinder.

    Checked against OSHA 3080, Hand and Power Tools.

  6. 6. The tang of a metal file, the part that fits into the handle, is annealed. Annealing makes the tang

    • A. harder, for better cutting
    • B. more resistant to rust
    • C. sharper along its edges
    • D. softer, so a handle can be threaded onto it
    Show the answer to question 6

    Answer: D. Annealing is a process used on hardened parts to soften them. A file is made of hardened tool steel, but its tang is annealed so a handle can be threaded onto it. Harder is the opposite of annealing. Always use a handle, because filing without one can cause injury.

    Remember: Annealing = softening a hardened part. The file's face and edges stay hard to cut; only the tang is softened for the handle.

    Checked against Introduction to Machining (Washington SBCTC open textbook), 5.8 Files.

  7. 7. Steel reinforcing bars are placed in concrete beams and slabs mainly because concrete is

    • A. strong in compression but weak in tension
    • B. weak in compression but strong in tension
    • C. too heavy to stand without support
    • D. unable to harden without steel inside
    Show the answer to question 7

    Answer: A. FHWA explains that the compressive strength of concrete is much greater than its tensile strength, and plain concrete tends to crack wherever there is enough tension. So designers place reinforcing bars wherever tension is present, to carry the tensile load. The second choice has the two strengths reversed.

    Remember: Concrete takes the squeeze, steel takes the pull. Rebar goes where the concrete would be in tension.

    Checked against FHWA-HRT-16-012, LTBP Summary: National Changes in Bridge Practices for Reinforcing Bars.

What Shop Information practice test 4 covers

10 questions in 6 minutes, the length and time limit of the Shop Information subtest on the computer ASVAB. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 4 spreads its questions over 10 topics:

TopicQuestions in test 4
Power tools1
Layout and marking1
Joints1
Hand tools1
Shop safety1
Metal and metalworking1
Building materials1
Wood and woodworking1
Fasteners1
Measuring tools1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Shop Information tests, and test 4 of the other subtests

What the Shop Information subtest covers, how it is used and the questions people ask about it are on the Shop Information practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Shop Information tests

Practice test 4 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.