Joining the Military

ASVAB Shop Information Practice Test 2

Free · No signup

Test 2 of 5 for Shop Information: 10 questions in 6 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 6 of Shop Information practice test 2

6 of the 10 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 10, with an explanation like these for every question.

  1. 1. The inch is defined as exactly 25.4 millimeters. A bolt 2 inches long is how long in millimeters?

    • A. 12.7 mm
    • B. 25.4 mm
    • C. 50.8 mm
    • D. 254 mm
    Show the answer to question 1

    Answer: C. Multiply inches by 25.4: 2 × 25.4 = 50.8 mm. NIST states the inch has been exactly 25.4 mm since 1959. Choosing 12.7 mm comes from dividing instead of multiplying, and 254 mm comes from moving the decimal point.

    Remember: Inches to millimeters: multiply by 25.4. Millimeters to inches: divide by 25.4. One inch is about 2.5 centimeters.

    Checked against NIST Office of Weights and Measures, SI Units: Length.

  2. 2. Which hand saw, with a fine-toothed blade held tight in a frame, is the right choice for cutting through a steel rod?

    • A. hacksaw
    • B. coping saw
    • C. crosscut saw
    • D. flush-cut saw
    Show the answer to question 2

    Answer: A. A hacksaw holds a fine-toothed blade in tension and is made for cutting metals and some plastics; its blade cuts on the push stroke. A coping saw also has a frame, but its narrow blade is meant for cutting curves in wood, and crosscut saws have large teeth for wood.

    Remember: Fine teeth for metal, coarse teeth for wood. For metal by hand, reach for the hacksaw and cut on the push stroke.

    Checked against Louisiana State University, Design Shop Safety Manual.

  3. 3. Before changing the bit in a portable electric drill, you should first

    • A. run the drill briefly to clear chips
    • B. lock the trigger in the on position
    • C. set the drill down on its side
    • D. unplug the drill from the outlet
    Show the answer to question 3

    Answer: D. OSHA says to disconnect power tools when they are not in use, before servicing or cleaning, and when changing accessories such as blades, bits, and cutters. A plugged-in drill can start if the trigger is bumped. Locking the trigger on is the opposite of safe.

    Remember: Changing a blade, bit, or cutter? Disconnect the tool from power first. No power means no accidental start.

    Checked against OSHA 3080, Hand and Power Tools.

  4. 4. Compared with sapwood, the heartwood of a tree is usually

    • A. lighter in color and more prone to decay
    • B. darker in color and more decay resistant
    • C. wetter and easier to bend
    • D. the youngest wood in the trunk
    Show the answer to question 4

    Answer: B. Heartwood runs from the pith to the sapwood, and its cells no longer take part in the tree's life. Deposits such as gums and resins usually make it darker and more decay resistant. Sapwood is the pale wood near the outside of the log and is more likely to decay.

    Remember: Heart = center = darker and more durable. Sap = outside = paler and decays sooner.

    Checked against USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282), Glossary: Heartwood and Sapwood.

  5. 5. A step-shaped recess cut along the edge or end of a board, often used to set the back panel into a cabinet, is called a

    • A. dado
    • B. mortise
    • C. rabbet
    • D. miter
    Show the answer to question 5

    Answer: C. A rabbet is a step cut into the edge or end of a board, basically a dado cut along the edge, and it is often used at the back of cabinets to attach the back to the sides. A dado is the tempting choice, but a dado is a groove cut into the board, while a rabbet is a step along its edge (a half-dado).

    Remember: Rabbet = a step along the edge or end of a board (a half-dado). Dado = a groove cut into the board.

    Checked against University of Illinois School of Art and Design, Woodworking: Making Joints.

  6. 6. Before nailing into dense hardwood, a carpenter drills a lead hole slightly smaller than the nail. The main benefit is that the hole

    • A. reduces splitting of the wood
    • B. lets the nail pull out more easily
    • C. keeps the nail from rusting
    • D. allows a shorter nail to be used
    Show the answer to question 6

    Answer: A. The Wood Handbook says lead holes about 90% of the nail diameter prevent or reduce splitting, especially in dense species, and nails in such holes actually have somewhat greater withdrawal resistance. So the hole does not make the nail easier to pull out, and it has no effect on rust or needed length.

    Remember: Dense wood plus a big nail can split the board. A pilot hole a little smaller than the fastener prevents splitting while still gripping.

    Checked against USDA Forest Products Laboratory, Wood Handbook (FPL-GTR-282), ch. 8, Fastenings.

What Shop Information practice test 2 covers

10 questions in 6 minutes, the length and time limit of the Shop Information subtest on the computer ASVAB. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 2 spreads its questions over 10 topics:

TopicQuestions in test 2
Measuring tools1
Hand tools1
Shop safety1
Wood and woodworking1
Joints1
Fasteners1
Power tools1
Building materials1
Metal and metalworking1
Layout and marking1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Shop Information tests, and test 2 of the other subtests

What the Shop Information subtest covers, how it is used and the questions people ask about it are on the Shop Information practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Shop Information tests

Practice test 2 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.