Joining the Military

ASVAB Shop Information Practice Test 5

Free · No signup

Test 5 of 5 for Shop Information: 10 questions in 6 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 6 of Shop Information practice test 5

6 of the 10 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 10, with an explanation like these for every question.

  1. 1. A Phillips screwdriver is recognized by a tip that is shaped like

    • A. a single flat blade
    • B. a six-pointed star
    • C. a square peg
    • D. an X
    Show the answer to question 1

    Answer: D. A Phillips screwdriver is much like a standard screwdriver, except that its tip is shaped like an X to fit the crossed slots of a Phillips screw. A single flat blade describes the standard (slotted) screwdriver, which is the tempting mistake.

    Remember: Phillips = cross. Whatever the type, pick a tip that fits the screw snugly so it does not slip.

    Checked against Louisiana State University College of Art and Design, Design Shop Safety Manual.

  2. 2. In a half-lap joint, the two boards fit together flush because

    • A. half the thickness of each board is removed where they overlap
    • B. the end of one board is nailed to the face of the other
    • C. both boards are cut at a 45 degree angle
    • D. wedge-shaped pins on one board lock into the other
    Show the answer to question 2

    Answer: A. In a half-lap joint, half of each of the two boards is removed where they cross, so the boards join flush with one another. Nailing an end to a face is a butt joint, 45 degree cuts make a miter joint, and wedge-shaped pins describe a dovetail.

    Remember: Half-lap: each board gives up half its thickness, so together they are one board thick.

    Checked against University of Illinois, College of Fine and Applied Arts: Woodworking Joints.

  3. 3. OSHA's guide to hand and power tools says knives and scissors must be kept sharp because dull tools

    • A. cut too quickly to control
    • B. make sparks near flammable liquids
    • C. can cause more hazards than sharp ones
    • D. cannot be stored safely
    Show the answer to question 3

    Answer: C. OSHA states that knives and scissors must be sharp because dull tools can cause more hazards than sharp ones. A dull edge has to be forced, and a tool that is being forced is more likely to slip. A dull tool cuts slowly, not quickly.

    Remember: Sharp is safer: less force on the tool means more control over where it goes.

    Checked against OSHA 3080, Hand and Power Tools.

  4. 4. Which measuring tool can take outside, inside, depth and step measurements with one instrument?

    • A. Outside micrometer
    • B. Slide caliper
    • C. Feeler gauge
    • D. Spirit level
    Show the answer to question 4

    Answer: B. A slide caliper has outside jaws, inside jaws, a depth blade and step surfaces, so one tool takes all four kinds of measurement. An outside micrometer is the tempting mistake: it is precise, but it measures only outside dimensions.

    Remember: Slide caliper = four jobs: outside, inside, depth, step. It comes in vernier, dial and digital styles.

    Checked against Introduction to Machining (Open Washington Pressbooks), 4.3 Direct Read Measuring Equipment.

  5. 5. Nails with a galvanized (zinc) coating are chosen mainly for jobs where

    • A. the nail must be driven into concrete
    • B. resistance to corrosion and staining is important
    • C. the nail head must be hidden
    • D. the wood is too hard to nail by hand
    Show the answer to question 5

    Answer: B. Nails with galvanized coatings, such as zinc, are intended mainly for uses where resistance to corrosion and staining matters, which is why they are common in outdoor work. The coating is not there to make the nail harder or easier to drive.

    Remember: Galvanized = zinc coated = made to resist rust. Use it wherever the fastener will get wet.

    Checked against USDA Forest Products Laboratory, Wood Handbook: Wood as an Engineering Material (FPL-GTR-282).

  6. 6. After staking out a rectangular slab, a builder measures both diagonals between opposite corners. The corners are square when the two diagonals are

    • A. in a 3 to 4 ratio
    • B. each as long as the longer side
    • C. longer than the two sides added together
    • D. equal in length
    Show the answer to question 6

    Answer: D. After staking out the area, squareness is checked by measuring the diagonals between opposite corners: they should be equal. The 3 to 4 ratio is the tempting mistake. It belongs to the 3-4-5 method used to set one square corner, where it describes the two sides, not the diagonals.

    Remember: Equal diagonals = square corners. If one diagonal is longer, shift the stakes until the two match.

    Checked against QUIKRETE, Layout Basics for Slabs and Footers.

What Shop Information practice test 5 covers

10 questions in 6 minutes, the length and time limit of the Shop Information subtest on the computer ASVAB. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 5 spreads its questions over 10 topics:

TopicQuestions in test 5
Hand tools1
Joints1
Shop safety1
Measuring tools1
Fasteners1
Layout and marking1
Building materials1
Wood and woodworking1
Metal and metalworking1
Power tools1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Shop Information tests, and test 5 of the other subtests

What the Shop Information subtest covers, how it is used and the questions people ask about it are on the Shop Information practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Shop Information tests

Practice test 5 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.