Joining the Military

ASVAB Mechanical Comprehension Practice Test 2

Free · No signup

Test 2 of 5 for Mechanical Comprehension: 15 questions in 22 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 7 of Mechanical Comprehension practice test 2

7 of the 15 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 15, with an explanation like these for every question.

  1. 1. The diagram shows a lever like a wheelbarrow: the fulcrum is at the left end, a 200 lb load sits 1.5 ft from the fulcrum, and the effort lifts at the right end, 6 ft from the fulcrum. Ignoring the bar's weight, what upward effort holds the load?

    200 lb?1.5 ft6 ft
    • A. 200 lb
    • B. 50 lb
    • C. 800 lb
    • D. 150 lb
    Show the answer to question 1

    Answer: B. The load is between the fulcrum and the effort, as in a wheelbarrow. Effort x 6 = 200 x 1.5, so effort = 50 lb. The 800 lb choice swaps the two arms. The effort arm is longer, so the effort is smaller than the load.

    Remember: Wherever the load sits, measure both arms from the fulcrum: effort x effort arm = load x load arm.

    Checked against OpenStax College Physics 2e, 9.5 Simple Machines.

  2. 2. In the diagram, a 150 lb load hangs from one movable pulley supported by two rope strands, with the rope passing over one fixed pulley. Ignoring friction and the pulley's weight, what pull holds the load?

    150 lbPull
    • A. 150 lb
    • B. 300 lb
    • C. 50 lb
    • D. 75 lb
    Show the answer to question 2

    Answer: D. Two strands hold up the movable pulley, and each carries the same tension, so the pull is 150 / 2 = 75 lb. The 150 lb choice treats the system like a single fixed pulley, which only changes direction.

    Remember: Count the strands that hold up the movable pulley; the ideal pull is the load divided by that number.

    Checked against OpenStax College Physics 2e, 9.5 Simple Machines.

  3. 3. The diagram shows three gears in a row. The first gear (24 teeth) turns clockwise. Which way does the third gear (36 teeth) turn?

    Gear A24 teethdriverGear B12 teethGear C36 teeth
    • A. It cannot turn at all
    • B. It rocks back and forth
    • C. Counterclockwise
    • D. Clockwise
    Show the answer to question 3

    Answer: D. Each pair of meshing gears turns in opposite directions. The first gear turns clockwise, so the middle gear turns counterclockwise and the third gear turns clockwise again. The direction flips at each of the two meshes, so the first and third gears match.

    Remember: Meshing gears alternate direction: 1st and 3rd gears in a row turn the same way, 2nd and 4th the opposite way.

    Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.

  4. 4. The ramp in the diagram is 15 ft long and rises 5 ft. What is its ideal mechanical advantage?

    300 lb15 ft5 ft
    • A. 3
    • B. 5
    • C. 15
    • D. 20
    Show the answer to question 4

    Answer: A. For an inclined plane, ideal mechanical advantage is the slope length divided by the height: 15 / 5 = 3. So, without friction, a 300 lb load needs only a 100 lb push along the ramp. The 5 choice is just the height.

    Remember: Inclined plane IMA = slope length / height. Longer, gentler ramps give a bigger advantage.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  5. 5. A well windlass has a crank handle 18 inches from the center of its axle and a rope drum with a radius of 3 inches. Ignoring friction, what force on the crank handle lifts a 240 lb bucket?

    • A. 240 lb
    • B. 80 lb
    • C. 40 lb
    • D. 1,440 lb
    Show the answer to question 5

    Answer: C. A crank and drum is a wheel and axle with IMA = 18 / 3 = 6. The effort is 240 / 6 = 40 lb. The 1,440 lb choice multiplies by the advantage instead of dividing; a crank reduces the force needed.

    Remember: Effort on a wheel and axle = load x axle radius / wheel (or crank) radius.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  6. 6. A bolt has 16 threads per inch. How far does a nut move along the bolt when it is turned 8 full turns?

    • A. 1/16 inch
    • B. 8 inches
    • C. 2 inches
    • D. 1/2 inch
    Show the answer to question 6

    Answer: D. The pitch, the distance a screw advances in one turn, is 1/16 inch for 16 threads per inch. Eight turns move the nut 8 x 1/16 = 1/2 inch. The 2 inch choice divides 16 by 8 instead.

    Remember: Pitch = 1 / threads per inch. Distance moved = number of turns x pitch.

    Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.

  7. 7. A hydraulic jack has a small piston 1 inch in diameter and a large piston 4 inches in diameter. If 30 lb pushes on the small piston, what force does the large piston exert? (Ignore friction.)

    • A. 30 lb
    • B. 120 lb
    • C. 480 lb
    • D. 7.5 lb
    Show the answer to question 7

    Answer: C. Force scales with piston area, and area scales with the square of diameter. A diameter 4 times larger gives 4 x 4 = 16 times the area, so the output is 30 x 16 = 480 lb. The 120 lb choice uses the diameter ratio instead of the area ratio.

    Remember: Pascal: F2 / F1 = A2 / A1. When given diameters, square the diameter ratio to get the area ratio.

    Checked against OpenStax College Physics 2e, 11.5 Pascal's Principle.

What Mechanical Comprehension practice test 2 covers

15 questions in 22 minutes, the length and time limit of the Mechanical Comprehension subtest on the computer ASVAB. 6 of them are asked with a diagram. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 2 spreads its questions over 13 topics:

TopicQuestions in test 2
Levers2
Pulleys1
Gears2
Ramps and inclined planes1
Wheel and axle1
Screws and wedges1
Hydraulics1
Springs1
Structures and loads1
Materials and their strength1
Motion1
Fluids1
Pressure1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Mechanical Comprehension tests, and test 2 of the other subtests

What the Mechanical Comprehension subtest covers, how it is used and the questions people ask about it are on the Mechanical Comprehension practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Mechanical Comprehension tests

Practice test 2 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.