Joining the Military

ASVAB Mechanical Comprehension Practice Test 3

Free · No signup

Test 3 of 5 for Mechanical Comprehension: 15 questions in 22 minutes, as on the computer test. None of its questions is in the other four tests.

Reviewed by Guilherme Correia, active-duty U.S. Air Force

1. Choose a test

2. Choose a version

Five versions, no question repeated between them. Take a new one each time so the score measures what you learned, not what you remember.

3. Choose the timing

Free, no signup. Your answers stay on this device.

Questions 1 to 7 of Mechanical Comprehension practice test 3

7 of the 15 questions in this test, exactly as the test asks them. Choose your answer, then open the answer under each one. The test above gives all 15, with an explanation like these for every question.

  1. 1. The diagram shows a lever with the fulcrum at the left end, the effort applied 2 ft from the fulcrum, and a 10 lb load at the far end, 6 ft from the fulcrum, like a fishing rod or a shovel. What effort holds the load?

    ?10 lb2 ft6 ft
    • A. 10 lb
    • B. 5 lb
    • C. 30 lb
    • D. 60 lb
    Show the answer to question 1

    Answer: C. Effort x 2 ft = 10 lb x 6 ft, so the effort is 30 lb. When the effort is between the fulcrum and the load, the effort arm is shorter, so the mechanical advantage is less than 1. You gain speed and reach at the load, not force.

    Remember: If the effort is closer to the fulcrum than the load, expect to push harder than the load weighs.

    Checked against OpenStax College Physics 2e, 9.5 Simple Machines.

  2. 2. The diagram shows a 600 lb engine block lifted by a pulley system with two movable pulleys and four supporting strands. Ignoring friction and the pulleys' weight, what pull is needed?

    600 lbPull
    • A. 200 lb
    • B. 600 lb
    • C. 300 lb
    • D. 150 lb
    Show the answer to question 2

    Answer: D. Four strands share the load, so each carries 600 / 4 = 150 lb, and that is the pull on the free end. The 300 lb choice counts only two strands.

    Remember: Ideal pulley pull = load / number of strands holding up the movable pulleys.

    Checked against OpenStax College Physics 2e, 9.5 Simple Machines.

  3. 3. In the diagram, a 40-tooth gear drives a 10-tooth gear. How many turns does the 10-tooth gear make for each turn of the 40-tooth gear?

    Gear A40 teeth, driverGear B10 teeth
    • A. 1
    • B. 1/4
    • C. 4
    • D. 2
    Show the answer to question 3

    Answer: C. One turn of the 40-tooth gear pushes 40 teeth past the meshing point. The 10-tooth gear needs only 10 teeth per turn, so it turns 40 / 10 = 4 times. The smaller gear always turns faster.

    Remember: Turns of driven gear = driver teeth / driven teeth. Big gear driving a small gear gives more speed and less force.

    Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.

  4. 4. A 250 lb load is pushed up the 16 ft ramp shown to a platform 4 ft high. Ignoring friction, how much work is done on the load?

    250 lb16 ft4 ft
    • A. 5,000 ft-lb
    • B. 1,000 ft-lb
    • C. 4,000 ft-lb
    • D. 250 ft-lb
    Show the answer to question 4

    Answer: B. Without friction, the ramp needs the same work as lifting straight up: 250 lb x 4 ft = 1,000 ft-lb. The ramp lowers the force to 62.5 lb but makes it act over 16 ft, and 62.5 x 16 is still 1,000. The 4,000 choice uses the full load over the slope length.

    Remember: Machines cut force, not work. Ideal work = weight x height lifted, whatever path you take.

    Checked against OpenStax College Physics 2e, 9.5 Simple Machines.

  5. 5. A wheel and axle has a wheel radius of 10 inches and an axle radius of 2 inches. Ignoring friction, a 30 lb force on the rim of the wheel produces what force at the axle?

    • A. 300 lb
    • B. 150 lb
    • C. 60 lb
    • D. 6 lb
    Show the answer to question 5

    Answer: B. IMA = wheel radius / axle radius = 10 / 2 = 5, so the axle delivers 30 x 5 = 150 lb. The 6 lb choice divides by the advantage, which would be true only if the force went in at the axle.

    Remember: Force in at the big wheel comes out multiplied at the small axle; force in at the axle comes out reduced at the rim.

    Checked against OpenStax Physics, 9.3 Simple Machines.

  6. 6. A screw jack has a handle radius of 14 inches and a screw pitch of 0.25 inch. Ignoring friction, about what force on the handle lifts a 4,400 lb load?

    • A. 12.5 lb
    • B. 78.6 lb
    • C. 39.3 lb
    • D. 25.0 lb
    Show the answer to question 6

    Answer: A. Effort x handle circumference = load x pitch. The circumference is 2 x π x 14, about 88 in, so effort = 4,400 x 0.25 / 88, about 12.5 lb. The 25.0 lb choice uses π x radius instead of 2 x π x radius.

    Remember: Screw jack: effort x 2 x π x handle radius = load x pitch.

    Checked against Carnegie Mellon University, Introduction to Mechanisms, Ch. 2 Mechanisms and Simple Machines.

  7. 7. In a hydraulic press, the large piston has 5 times the area of the small piston. If the small piston is pushed down 10 inches, how far does the large piston rise? (Ignore friction and leaks.)

    • A. 5 inches
    • B. 50 inches
    • C. 2 inches
    • D. 10 inches
    Show the answer to question 7

    Answer: C. The fluid pushed out of the small cylinder fills the large one. With 5 times the area, the large piston rises 10 / 5 = 2 inches. It pushes with 5 times the force, so the work in and out stay equal.

    Remember: Hydraulic systems trade distance for force: the piston with more force moves a shorter distance.

    Checked against OpenStax College Physics 2e, 11.5 Pascal's Principle.

What Mechanical Comprehension practice test 3 covers

15 questions in 22 minutes, the length and time limit of the Mechanical Comprehension subtest on the computer ASVAB. 6 of them are asked with a diagram. This subtest does not count toward your AFQT; it feeds the scores the services use for jobs. Test 3 spreads its questions over 13 topics:

TopicQuestions in test 3
Levers1
Pulleys2
Gears2
Ramps and inclined planes1
Wheel and axle1
Screws and wedges1
Hydraulics1
Springs1
Structures and loads1
Materials and their strength1
Motion1
Fluids1
Pressure1

Questions and time limit: officialasvab.com, What to Expect, read October 3, 2026. The questions are original practice material; the topic names are this site's.

The other Mechanical Comprehension tests, and test 3 of the other subtests

What the Mechanical Comprehension subtest covers, how it is used and the questions people ask about it are on the Mechanical Comprehension practice test page. The format of all ten subtests and how the AFQT is scored are on the ASVAB practice test hub.

All five Mechanical Comprehension tests

Practice test 3 of the other subtests

Keep going

officialasvab.com (What to Expect), read October 3, 2026, for the number of questions and the time limit. The questions are original.

Results are estimates. Always verify with your finance office.

Reviewed by Guilherme Correia · Military Toolkit editorial

Military Toolkit is not affiliated with the Department of Defense or the ASVAB testing program. The questions are original practice material, not ASVAB questions.